Skip to main content

Alpine, TX Building Setbacks & Zoning: Lot Coverage Limits (2026)

Some Restrictions
Compiled from the official code textEditor Martyn O'NeillLast verified November 2026

Key Facts

R-1 maximum impervious coverage
60% all structures
R-2 maximum impervious coverage
60% all structures
R-3 interior lot
70%
R-3 corner lot
75%
R-1 minimum dwelling area
1000 Sq Ft footprint of home
R-1 density
One primary dwelling unit per lot

Summary

In Alpine, the R-1 one-family district limits impervious coverage to 60% all structures. The R-2 multi-family table prints the same 60%, while the R-3 apartment district allows an interior lot 70% and a corner lot 75%. Appendix C ties each cap to a site development table for the district.

Each site in the R-1 district shall be subject to the following site development regulations: Feature Regulations ... Residential density One primary dwelling unit per lot, not to include accessory structures Minimum dwelling areas (Footprint of Home) 1000 Sq Ft Maximum impervious coverage 60% all structures

Full Breakdown

Alpine does not regulate lot coverage in a stand-alone section. Appendix C of the Code of Ordinances prints a Maximum impervious coverage line inside each residential district's site development table. For the R-1 one-family district (Article I, Section II) that line reads 60% all structures. The same table adds the rules that shape what fits on the lot: residential density is one primary dwelling unit per lot, not to include accessory structures, and the minimum dwelling area (footprint of home) is 1000 Sq Ft. Off street parking is 2 off street minimum, and lot width minimum is 50 feet.

The R-2 multi-family table (Section III), written for duplexes, townhouses, triplexes and quadplexes, prints Maximum impervious coverage as 60% all structures. Its minimum dwelling area is 750 square feet per dwelling unit, counted as living area only. The R-3 apartment table (Section IV), written for apartment houses and multiple family dwellings, is the only residential district that steps the cap up: Interior lot 70%, corner lot 75%. R-3 apartment use also requires submittal of architectural plans, and off street parking is 1 per dwelling unit minimum.

The wording matters. The R-1 and R-2 lines say 60% all structures, which reads as a total for the structures on the site rather than a separate figure for the house alone. The accessory structure rules sit in the same table and sit inside that total: a temporary or accessory building is held to no more than 40% of the required rear yard, and a carport to no more than 40% of the required front, side or rear yard.

Because the cap is a district standard, it is checked when a building permit is requested, and a rezoning from R-1 to R-3 changes the allowed coverage for the lot.

Violations & Fines

The coverage tables print no penalty of their own. Impervious area above 60% all structures in R-1 or R-2, or above 70% on an R-3 interior lot or 75% on an R-3 corner lot, departs from the district regulation and is dealt with through the city's building permit and zoning process rather than a fine printed in these tables.

Frequently Asked Questions

How much of an R-1 lot in Alpine can be covered?
The R-1 site development table in Appendix C sets Maximum impervious coverage at 60% all structures. The same table limits residential density to one primary dwelling unit per lot, not to include accessory structures.
Is the coverage cap higher in Alpine's apartment district?
Yes. The R-3 apartment table prints Interior lot 70%, corner lot 75%, compared with 60% all structures in the R-1 and R-2 tables. R-3 apartment use also requires submittal of architectural plans.
Do sheds and carports count toward Alpine's coverage cap?
The R-1 cap is printed as 60% all structures, so accessory buildings sit inside the same table. A temporary or accessory building is held to no more than 40% of the required rear yard and a carport to no more than 40% of the required front, side or rear yard.
What is the minimum house size in Alpine's R-1 district?
The R-1 table prints a minimum dwelling area, listed as footprint of home, of 1000 Sq Ft. In the R-2 multi-family table the minimum dwelling area is 750 square feet per dwelling unit, counted as living area only.

Sources & Official References

Other rules in Alpine

All Alpine rules

Texas rules heatmap·Compare Alpine to another location·View the Texas building setbacks & zoning overview

Get notified when Lot Coverage Limits in Alpine, TX changes

We'll email you the moment we detect a change in the code. No spam, unsubscribe anytime.

We'll never sell or share your email. One-click unsubscribe in every email.

See something wrong?

Help us keep this page accurate. If you notice an error or outdated information, let us know.